[Help] check_mem.sh plugin configuration

[sh.shekhar89]

Hi Friends,

i am trying to configure check_mem.sh plugin to check my server memory usage.

I am able to telnet both servers from each other.

plugin is working for localhost (nagios server) but not working for my remote server(clinet)[ screenshot attcahed]

Please help me to configure it
I am getting error " NRPE: Command 'check_mem' not defined "

Here is my configuration :
Nagios Server nrpe.cfg
"command[check_mem]=/usr/local/nagios/libexec/check_mem.sh -w 85 -c 90"
Nagios server commands.cfg ::

"# check_nrpe_memory
define command {
command_name check_mem
command_line /usr/lib/nagios/plugins/check_mem.sh -w $ARG1$ -c $ARG2$
}"

Nagios Server Service Defination ::

"define service{
use local-service
host_name Test-Linux
service_description Check RAM
check_command check_nrpe!check_mem
}
"
Can some one guide me to configure it?? I have some load performance test on linux(client) we want to monitor the server memory usage from nagios.

[abrist]

You need to check the remote hosts nrpe.cfg for the command. The nrpe.cfg on the nagios server will not apply to remote checks. Can you post the remote hosts nrpe.cfg?

[sh.shekhar89]

Hi abrist,

Hope you doing fine...

here is the remote host nrpe.cfg file :

Code: Select all

#############################################################################
# Sample NRPE Config File 
# Written by: Ethan Galstad (nagios@nagios.org)
# 
# Last Modified: 11-23-2007
#
# NOTES:
# This is a sample configuration file for the NRPE daemon.  It needs to be
# located on the remote host that is running the NRPE daemon, not the host
# from which the check_nrpe client is being executed.
#############################################################################


# LOG FACILITY
# The syslog facility that should be used for logging purposes.

log_facility=daemon



# PID FILE
# The name of the file in which the NRPE daemon should write it's process ID
# number.  The file is only written if the NRPE daemon is started by the root
# user and is running in standalone mode.

pid_file=/var/run/nrpe.pid



# PORT NUMBER
# Port number we should wait for connections on.
# NOTE: This must be a non-priviledged port (i.e. > 1024).
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd

server_port=5666



# SERVER ADDRESS
# Address that nrpe should bind to in case there are more than one interface
# and you do not want nrpe to bind on all interfaces.
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd

#server_address=127.0.0.1



# NRPE USER
# This determines the effective user that the NRPE daemon should run as.  
# You can either supply a username or a UID.
# 
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd

nrpe_user=nagios



# NRPE GROUP
# This determines the effective group that the NRPE daemon should run as.  
# You can either supply a group name or a GID.
# 
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd

nrpe_group=nagios



# ALLOWED HOST ADDRESSES
# This is an optional comma-delimited list of IP address or hostnames 
# that are allowed to talk to the NRPE daemon. Network addresses with a bit mask
# (i.e. 192.168.1.0/24) are also supported. Hostname wildcards are not currently 
# supported.
#
# Note: The daemon only does rudimentary checking of the client's IP
# address.  I would highly recommend adding entries in your /etc/hosts.allow
# file to allow only the specified host to connect to the port
# you are running this daemon on.
#
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd

allowed_hosts=127.0.0.1
 


# COMMAND ARGUMENT PROCESSING
# This option determines whether or not the NRPE daemon will allow clients
# to specify arguments to commands that are executed.  This option only works
# if the daemon was configured with the --enable-command-args configure script
# option.  
#
# *** ENABLING THIS OPTION IS A SECURITY RISK! *** 
# Read the SECURITY file for information on some of the security implications
# of enabling this variable.
#
# Values: 0=do not allow arguments, 1=allow command arguments

dont_blame_nrpe=0



# BASH COMMAND SUBTITUTION
# This option determines whether or not the NRPE daemon will allow clients
# to specify arguments that contain bash command substitutions of the form
# $(...).  This option only works if the daemon was configured with both 
# the --enable-command-args and --enable-bash-command-substitution configure 
# script options.
#
# *** ENABLING THIS OPTION IS A HIGH SECURITY RISK! *** 
# Read the SECURITY file for information on some of the security implications
# of enabling this variable.
#
# Values: 0=do not allow bash command substitutions, 
#         1=allow bash command substitutions

allow_bash_command_substitution=0



# COMMAND PREFIX
# This option allows you to prefix all commands with a user-defined string.
# A space is automatically added between the specified prefix string and the
# command line from the command definition.
#
# *** THIS EXAMPLE MAY POSE A POTENTIAL SECURITY RISK, SO USE WITH CAUTION! ***
# Usage scenario: 
# Execute restricted commmands using sudo.  For this to work, you need to add
# the nagios user to your /etc/sudoers.  An example entry for alllowing 
# execution of the plugins from might be:
#
# nagios          ALL=(ALL) NOPASSWD: /usr/lib/nagios/plugins/
#
# This lets the nagios user run all commands in that directory (and only them)
# without asking for a password.  If you do this, make sure you don't give
# random users write access to that directory or its contents!

# command_prefix=/usr/bin/sudo 



# DEBUGGING OPTION
# This option determines whether or not debugging messages are logged to the
# syslog facility.
# Values: 0=debugging off, 1=debugging on

debug=0



# COMMAND TIMEOUT
# This specifies the maximum number of seconds that the NRPE daemon will
# allow plugins to finish executing before killing them off.

command_timeout=60



# CONNECTION TIMEOUT
# This specifies the maximum number of seconds that the NRPE daemon will
# wait for a connection to be established before exiting. This is sometimes
# seen where a network problem stops the SSL being established even though
# all network sessions are connected. This causes the nrpe daemons to
# accumulate, eating system resources. Do not set this too low.

connection_timeout=300



# WEEK RANDOM SEED OPTION
# This directive allows you to use SSL even if your system does not have
# a /dev/random or /dev/urandom (on purpose or because the necessary patches
# were not applied). The random number generator will be seeded from a file
# which is either a file pointed to by the environment valiable $RANDFILE
# or $HOME/.rnd. If neither exists, the pseudo random number generator will
# be initialized and a warning will be issued.
# Values: 0=only seed from /dev/[u]random, 1=also seed from weak randomness

#allow_weak_random_seed=1



# INCLUDE CONFIG FILE
# This directive allows you to include definitions from an external config file.

#include=<somefile.cfg>



# INCLUDE CONFIG DIRECTORY
# This directive allows you to include definitions from config files (with a
# .cfg extension) in one or more directories (with recursion).

#include_dir=<somedirectory>
#include_dir=<someotherdirectory>



# COMMAND DEFINITIONS
# Command definitions that this daemon will run.  Definitions
# are in the following format:
#
# command[<command_name>]=<command_line>
#
# When the daemon receives a request to return the results of <command_name>
# it will execute the command specified by the <command_line> argument.
#
# Unlike Nagios, the command line cannot contain macros - it must be
# typed exactly as it should be executed.
#
# Note: Any plugins that are used in the command lines must reside
# on the machine that this daemon is running on!  The examples below
# assume that you have plugins installed in a /usr/local/nagios/libexec
# directory.  Also note that you will have to modify the definitions below
# to match the argument format the plugins expect.  Remember, these are
# examples only!


# The following examples use hardcoded command arguments...

command[check_users]=/usr/local/nagios/libexec/check_users -w 5 -c 10
command[check_load]=/usr/local/nagios/libexec/check_load -w 15,10,5 -c 30,25,20
command[check_hda1]=/usr/local/nagios/libexec/check_disk -w 20% -c 10% -p /dev/hda1
command[check_zombie_procs]=/usr/local/nagios/libexec/check_procs -w 5 -c 10 -s Z
command[check_total_procs]=/usr/local/nagios/libexec/check_procs -w 150 -c 200 



# The following examples allow user-supplied arguments and can
# only be used if the NRPE daemon was compiled with support for 
# command arguments *AND* the dont_blame_nrpe directive in this
# config file is set to '1'.  This poses a potential security risk, so
# make sure you read the SECURITY file before doing this.

#command[check_users]=/usr/local/nagios/libexec/check_users -w $ARG1$ -c $ARG2$
#command[check_load]=/usr/local/nagios/libexec/check_load -w $ARG1$ -c $ARG2$
#command[check_disk]=/usr/local/nagios/libexec/check_disk -w $ARG1$ -c $ARG2$ -p $ARG3$
#command[check_procs]=/usr/local/nagios/libexec/check_procs -w $ARG1$ -c $ARG2$ -s $ARG3$

[abrist]

Ah, you do not have that command defined in the remote hosts nrpe.cfg. Add the following line to the remote hosts nrpe.cfg and then restart nrpe/xinetd on the remote host:

Code: Select all

command[check_mem]=/usr/local/nagios/libexec/check_mem.sh -w 85 -c 90

[sh.shekhar89]

hi abrist,

after adding the lines to remote host nrpe.cfg file, i restarted the services, but now i am getting error : "NRPE: Unable to read output "

any changes i have to do again on both server and remote client??

[abrist]

Are you using this memory check on any other hosts? It looks like you have an arg mismatch - the check expects the warning and critical thresholds to be passed:

Code: Select all

command_line /usr/lib/nagios/plugins/check_mem.sh -w $ARG1$ -c $ARG2$

But the remote nrpe is configured with hard coded thresholds (like the nagios XI nrpe.cfg mem check):

Code: Select all

command[check_mem]=/usr/local/nagios/libexec/check_mem.sh -w 85 -c 90

If you are already using this nrpe check for other hosts, we should alter the remote host nrpe.cfg. If you are not using the mem check on any other hosts, you may want to decide if you want the thresholds configurable from the XI UI, or hard-coded into the remote hosts nrp.cfg configuration for the command.