Nagios Support Forum

This can be done, but to my knowledge only on a per-contact or
per-contactgroup basis. So essentially when that person logs into =
Nagios,
they only get the view of what they're responsible for.

If this interests you, I can follow-up with more detail.

jc

> -----Original Message-----
> From: [email protected]
> [mailto:[email protected]]
> Sent: Wednesday, February 12, 2003 10:08 AM
> To: Russell Scibetti
> Cc: [email protected]
> Subject: Antwort: Re: [Nagios-devel] status.cgi with only=20
> some services
>=20
>=20
>=20
> Hi Russell,
>=20
> Thank you for your tip.
> I'm sorry to say that this is not, what I'm looking for. I do=20
> not want to
> display all the services of one host, but only some of them.
>=20
> Freundliche Gr=FC=DFe
> Bernd Str=F6=DFenreuther
>=20
> -------------------------------------------------------------
> Sparda-Datenverarbeitung eG
> Server-Prozessmanagement / eBIS
> Freiligrathstra=DFe 32, 90482 N=FCrnberg
> Tel: 0911 / 54 86-802
> Fax: 0911 / 54 86-177
> mailto:[email protected]
>=20
>=20
>=20
> =20
> =20
> =20
> Russell =20
> =20
> =20
> Scibetti An: =20
> [email protected] =20
> =20
> [email protected] =20
> =20
> rix.com> Thema: Re:=20
> [Nagios-devel] status.cgi with only some services =20
> =20
> =20
> =20
> =20
> 11.02.03 =20
> =20
> =20
> 18:36 =20
> =20
> =20
> =20
> =20
> =20
> =20
> =20
> =20
>=20
>=20
>=20
>=20
> What you should be able to do, is in the configs, define a hostgroup
> with the specific hosts you want to see, and then add
> "&hostgroup=3Dhost_group_name" to the end of the URL. Leave=20
> the host=3Dall.
> This will show the status of all services for hosts inside=20
> that hostgroup.
>=20
> Russell Scibetti
>=20
> [email protected] wrote:
>=20
> >Hi out there,
> >
> >Where can I find a documentation of all the parameters I can give to
> >status.cgi?
> >I did not yet manage to find some documentation.
> >
> >What I want is a list of all states like
> >/nagios/cgi-bin/status.cgi?host=3Dall
> >prints it out, but I don't want all the services to be=20
> shown, but only a
> >view of them. I would need the possibility to give it the=20
> names of some
> >services by parameter, so that it knows, which of them I=20
> want to display.
> >Is this possible?
> >
> >Freundliche Gr=FC=DFe
> >Bernd Str=F6=DFenreuther
> >
> >-------------------------------------------------------------
> >Sparda-Datenverarbeitung eG
> >Server-Prozessmanagement / eBIS
> >Freiligrathstra=DFe 32, 90482 N=FCrnberg
> >Tel: 0911 / 54 86-802
> >Fax: 0911 / 54 86-177
> >mailto:[email protected]
> >
> >
> >
> >
> >-------------------------------------------------------
> >This SF.NET email is sponsored by:
> >SourceForge Enterprise Edition + IBM + LinuxWorld =3Domething 2 See!
> >http://www.vasoftw

...[email truncated]...


This post was automatically imported from historical nagios-devel mailing list archives
Original poster: [email protected]