Page 1 of 3
service check timeouts
Posted: Mon Oct 05, 2015 5:45 am
by quental
Linux red hat Enterprise 5 x86_64
Manual installation (reléase 2012R2.2)
Hi,
we have a problem when checking service in one node.
On /var/log/messages, we can see an error with xinted service:
Some days the checks running well, but another days fails.
we change value parameters in /etc/xinted.conf, but there isn´t running well.
any sugestion?
regards.
Re: service check timeouts
Posted: Mon Oct 05, 2015 12:31 pm
by tmcdonald
Check out page 3 of this guide:
https://assets.nagios.com/downloads/nag ... utions.pdf
Usually this means either the Nagios host is not in the list of allowed IP addresses, or that SSL support was not compiled in. However, the fact that this is intermittent is odd. You may have a limitation being hit - the same section in the PDF goes over removing the limits in xinetd to the connections from remote machines.
Re: service check timeouts
Posted: Tue Oct 06, 2015 5:48 am
by quental
Hi,
we have made some changes in the following files:
/etc/xinetd.d/nrpe (append this lines)
/usr/local/nagios/nrpe.cfg (change value 120 to 180)
/etc/xinetd.conf (change value cps
after that, we will see if the problems are reproduced...
thanks.
Re: service check timeouts
Posted: Tue Oct 06, 2015 9:24 am
by hsmith
Let us know what you come up with. Thanks!
Re: service check timeouts
Posted: Fri Oct 09, 2015 5:54 am
by quental
Hi,
after changes the problem has occurred again.
any suggestions?
It is critical to us that this problem can be corrected somehow
Regards.
Javier
Re: service check timeouts
Posted: Fri Oct 09, 2015 1:10 pm
by tgriep
Could you post how the service check is defined on the Nagios Xi system that is giving you issues?
Also, are there any errors in the log file on the XI system?
Can you check this log file and post any errors for that check.
Re: service check timeouts
Posted: Wed Oct 21, 2015 5:28 am
by quental
Hi,
our check-nrpe definiton is attached.
in logs, we only see this:
Code: Select all
[1444255200] CURRENT SERVICE STATE: prometeo-bp.inversis.com;Servidor websvc1;OK;HARD;1;WEBLOGIC SERVER websvc1 is RUNNING since 00:57:21 Oct02 con usuario ets
[1444255200] CURRENT SERVICE STATE: prometeo-bp.inversis.com;Servidor websvc_batch1;OK;HARD;1;WEBLOGIC SERVER websvc_batch1 is RUNNING since 00:16:42 Sep24 con usuario ets
[1444255200] CURRENT SERVICE STATE: prometeo-bp.inversis.com;Servidor websvc_crit1;OK;HARD;1;WEBLOGIC SERVER websvc_crit1 is RUNNING since 00:17:20 Oct06 con usuario ets
[1444255200] CURRENT SERVICE STATE: prometeo-bp.inversis.com;Sincronizacion horaria servidor NTP;OK;HARD;1;NTP OK: Offset 0.0002744197845 secs
[1444255200] CURRENT SERVICE STATE: prometeo-bp.inversis.com;Tamano osb_server1.out;OK;HARD;1;FILE OK: All files (1) fall within requested parameters, SIZE is 95 MB
[1444255200] CURRENT SERVICE STATE: prometeo-bp.inversis.com;WLADMIN_MIDDLE;OK;HARD;1;WEBLOGIC SERVER WLADMIN_MIDDLE is RUNNING since 01:46:18 Aug30 con usuario ets
[1444255200] CURRENT SERVICE STATE: prometeo-bp.inversis.com;WLADMIN_OFICINA;OK;HARD;1;WEBLOGIC SERVER WLADMIN_OFICINA_MIG is RUNNING since 00:24:16 Aug30 con usuario ets
[1444255258] SERVICE ALERT: prometeo-bp.inversis.com;/opt Disk Usage;OK;HARD;5;76187688 64161584 8101844 89% /opt
[1444260658] SERVICE ALERT: prometeo-bp.inversis.com;/opt Disk Usage;WARNING;SOFT;1;76187688 64315916 7947512 90% /opt
[1444260718] SERVICE ALERT: prometeo-bp.inversis.com;/opt Disk Usage;WARNING;SOFT;2;76187688 64317328 7946100 90% /opt
[1444260778] SERVICE ALERT: prometeo-bp.inversis.com;/opt Disk Usage;WARNING;SOFT;3;76187688 64317512 7945916 90% /opt
[1444260838] SERVICE ALERT: prometeo-bp.inversis.com;/opt Disk Usage;WARNING;SOFT;4;76187688 64318856 7944572 90% /opt
[1444260898] SERVICE ALERT: prometeo-bp.inversis.com;/opt Disk Usage;WARNING;HARD;5;76187688 64319824 7943604 90% /opt
[1444262638] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador B_ADPTFIX_ACC_PROF;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262638] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador B_INTEMBSWIF_RF;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262638] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador RoutNomuranacEjec;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262639] SERVICE ALERT: prometeo-bp.inversis.com;Servidor osb_server1;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262639] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador B_NOMURA;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262639] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador B_RRS_BACKOFFICE;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262640] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador B_QVTRADER44;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262640] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador B_QMAB;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262640] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador B_QACCIONES;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262641] SERVICE ALERT: prometeo-bp.inversis.com;Servidor CAS1;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262641] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador B_QSMARTGATEFIX5;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262641] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador B_DISPARO_TS;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262642] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador B_CONTENIDOS;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262642] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador B_BACKOFFICEWS;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262642] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador B_QBATCH;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262648] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador B_INTEMBSWIF_LIQ;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262648] SERVICE ALERT: prometeo-bp.inversis.com;Servidor middleware1;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262648] SERVICE ALERT: prometeo-bp.inversis.com;Adaptador B_QGESTORAS;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262649] SERVICE ALERT: prometeo-bp.inversis.com;Servidor openfinance2;CRITICAL;HARD;1;(Service Check Timed Out)
[1444262649] SERVICE ALERT: prometeo-bp.inversis.com;Servidor auxiliar1;CRITICAL;HARD;1;(Service Check Timed Out)
Re: service check timeouts
Posted: Wed Oct 21, 2015 12:30 pm
by lmiltchev
How did you install the Linux agent (NRPE + Nagios plugins) on the remote machine? Did you follow
this document?
Run the following commands from the command line and show the output in code wraps:
On the client (remote machine):
Code: Select all
ifconfig
ps axuw | grep nrpe
netstat -at | grep nrpe
iptables -nL
cat /etc/xinetd.d/nrpe
cat /usr/local/nagios/etc/nrpe.cfg
Code: Select all
/usr/local/nagios/libexec/check_nrpe -H <client ip>
nmap <client ip> -p 5666
Re: service check timeouts
Posted: Thu Nov 05, 2015 6:32 am
by quental
Hi.
Sorry for delay on the answer.
These are the results of executing commands:
On the client (remote machine):
Ifconfig
Code: Select all
bond0 Link encap:Ethernet HWaddr 78:E7:D1:56:2F:A0
inet addr:192.168.22.174 Bcast:192.168.22.255 Mask:255.255.255.0
UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
RX packets:15310368093 errors:0 dropped:0 overruns:0 frame:0
TX packets:23374593614 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:7376333710599 (6.7 TiB) TX bytes:9050306997183 (8.2 TiB)
bond1 Link encap:Ethernet HWaddr 78:E7:D1:56:2F:A1
inet addr:192.168.246.174 Bcast:192.168.246.255 Mask:255.255.255.0
UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
RX packets:2140684704 errors:0 dropped:0 overruns:0 frame:0
TX packets:4089258894 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:194759000627 (181.3 GiB) TX bytes:5675244772409 (5.1 TiB)
eth0 Link encap:Ethernet HWaddr 78:E7:D1:56:2F:A0
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:13800146411 errors:0 dropped:0 overruns:0 frame:0
TX packets:23374593614 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:6805854524735 (6.1 TiB) TX bytes:9050306997183 (8.2 TiB)
Interrupt:130 Memory:fb000000-fb7fffff
eth1 Link encap:Ethernet HWaddr 78:E7:D1:56:2F:A0
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:1510221682 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:570479185864 (531.3 GiB) TX bytes:0 (0.0 b)
Interrupt:178 Memory:fa000000-fa7fffff
eth2 Link encap:Ethernet HWaddr 78:E7:D1:56:2F:A1
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:2139774277 errors:0 dropped:0 overruns:0 frame:0
TX packets:4089258894 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:194664610338 (181.2 GiB) TX bytes:5675244772409 (5.1 TiB)
Interrupt:178 Memory:f9000000-f97fffff
eth3 Link encap:Ethernet HWaddr 78:E7:D1:56:2F:A1
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:910427 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:94390289 (90.0 MiB) TX bytes:0 (0.0 b)
Interrupt:75 Memory:f8000000-f87fffff
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:3884572687 errors:0 dropped:0 overruns:0 frame:0
TX packets:3884572687 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2203452673674 (2.0 TiB) TX bytes:2203452673674 (2.0 TiB)
ets 13175 0.0 0.0 63248 832 pts/2 S+ 10:36 0:00 grep nrpe
netstat -at | grep nrpe
Code: Select all
tcp 0 0 *:nrpe *:* LISTEN
tcp 0 0 prometeo-bp.inversis.c:nrpe nagiosprd01.inversis.:44092 TIME_WAIT
tcp 0 0 prometeo-bp.inversis.c:nrpe nagiosprd01.inversis.:44094 TIME_WAIT
tcp 0 0 prometeo-bp.inversis.c:nrpe nagiosprd01.inversis.:44145 TIME_WAIT
tcp 0 0 prometeo-bp.inversis.c:nrpe nagiosprd01.inversis.:44144 TIME_WAIT
tcp 0 0 prometeo-bp.inversis.c:nrpe nagiosprd01.inversis.:44147 TIME_WAIT
tcp 0 0 prometeo-bp.inversis.c:nrpe nagiosprd01.inversis.:44134 TIME_WAIT
tcp 0 0 prometeo-bp.inversis.c:nrpe nagiosprd01.inversis.:44112 TIME_WAIT
tcp 0 0 prometeo-bp.inversis.c:nrpe nagiosprd01.inversis.:44119 TIME_WAIT
tcp 0 0 prometeo-bp.inversis.c:nrpe nagiosprd01.inversis.:44110 TIME_WAIT
tcp 0 0 prometeo-bp.inversis.c:nrpe nagiosprd01.inversis.:44263 TIME_WAIT
tcp 0 0 prometeo-bp.inversis.c:nrpe nagiosprd01.inversis.:43975 TIME_WAIT
Code: Select all
# default: on
# description: NRPE (Nagios Remote Plugin Executor)
service nrpe
{
flags = REUSE
socket_type = stream
port = 5666
wait = no
user = nagios
group = nagios
server = /usr/local/nagios/bin/nrpe
server_args = -c /usr/local/nagios/etc/nrpe.cfg --inetd
log_on_failure += USERID
disable = no
only_from = 127.0.0.1 192.168.247.128
instances = UNLIMITED
per_source = UNLIMITED
}
Code: Select all
#############################################################################
# Sample NRPE Config File
# Written by: Ethan Galstad ([email protected])
#
# Last Modified: 11-23-2007
#
# NOTES:
# This is a sample configuration file for the NRPE daemon. It needs to be
# located on the remote host that is running the NRPE daemon, not the host
# from which the check_nrpe client is being executed.
#############################################################################
# LOG FACILITY
# The syslog facility that should be used for logging purposes.
log_facility=daemon
# PID FILE
# The name of the file in which the NRPE daemon should write it's process ID
# number. The file is only written if the NRPE daemon is started by the root
# user and is running in standalone mode.
pid_file=/var/run/nrpe.pid
# PORT NUMBER
# Port number we should wait for connections on.
# NOTE: This must be a non-priviledged port (i.e. > 1024).
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd
server_port=5666
# SERVER ADDRESS
# Address that nrpe should bind to in case there are more than one interface
# and you do not want nrpe to bind on all interfaces.
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd
#server_address=127.0.0.1
# NRPE USER
# This determines the effective user that the NRPE daemon should run as.
# You can either supply a username or a UID.
#
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd
nrpe_user=nagios
# NRPE GROUP
# This determines the effective group that the NRPE daemon should run as.
# You can either supply a group name or a GID.
#
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd
nrpe_group=nagios
# ALLOWED HOST ADDRESSES
# This is an optional comma-delimited list of IP address or hostnames
# that are allowed to talk to the NRPE daemon. Network addresses with a bit mask
# (i.e. 192.168.1.0/24) are also supported. Hostname wildcards are not currently
# supported.
#
# Note: The daemon only does rudimentary checking of the client's IP
# address. I would highly recommend adding entries in your /etc/hosts.allow
# file to allow only the specified host to connect to the port
# you are running this daemon on.
#
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd
allowed_hosts=127.0.0.1
# COMMAND ARGUMENT PROCESSING
# This option determines whether or not the NRPE daemon will allow clients
# to specify arguments to commands that are executed. This option only works
# if the daemon was configured with the --enable-command-args configure script
# option.
#
# *** ENABLING THIS OPTION IS A SECURITY RISK! ***
# Read the SECURITY file for information on some of the security implications
# of enabling this variable.
#
# Values: 0=do not allow arguments, 1=allow command arguments
dont_blame_nrpe=1
# BASH COMMAND SUBTITUTION
# This option determines whether or not the NRPE daemon will allow clients
# to specify arguments that contain bash command substitutions of the form
# $(...). This option only works if the daemon was configured with both
# the --enable-command-args and --enable-bash-command-substitution configure
# script options.
#
# *** ENABLING THIS OPTION IS A HIGH SECURITY RISK! ***
# Read the SECURITY file for information on some of the security implications
# of enabling this variable.
#
# Values: 0=do not allow bash command substitutions,
# 1=allow bash command substitutions
allow_bash_command_substitution=0
# COMMAND PREFIX
# This option allows you to prefix all commands with a user-defined string.
# A space is automatically added between the specified prefix string and the
# command line from the command definition.
#
# *** THIS EXAMPLE MAY POSE A POTENTIAL SECURITY RISK, SO USE WITH CAUTION! ***
# Usage scenario:
# Execute restricted commmands using sudo. For this to work, you need to add
# the nagios user to your /etc/sudoers. An example entry for alllowing
# execution of the plugins from might be:
#
# nagios ALL=(ALL) NOPASSWD: /usr/lib/nagios/plugins/
#
# This lets the nagios user run all commands in that directory (and only them)
# without asking for a password. If you do this, make sure you don't give
# random users write access to that directory or its contents!
# command_prefix=/usr/bin/sudo
# DEBUGGING OPTION
# This option determines whether or not debugging messages are logged to the
# syslog facility.
# Values: 0=debugging off, 1=debugging on
debug=0
# COMMAND TIMEOUT
# This specifies the maximum number of seconds that the NRPE daemon will
# allow plugins to finish executing before killing them off.
command_timeout=120
# CONNECTION TIMEOUT
# This specifies the maximum number of seconds that the NRPE daemon will
# wait for a connection to be established before exiting. This is sometimes
# seen where a network problem stops the SSL being established even though
# all network sessions are connected. This causes the nrpe daemons to
# accumulate, eating system resources. Do not set this too low.
connection_timeout=300
# WEEK RANDOM SEED OPTION
# This directive allows you to use SSL even if your system does not have
# a /dev/random or /dev/urandom (on purpose or because the necessary patches
# were not applied). The random number generator will be seeded from a file
# which is either a file pointed to by the environment valiable $RANDFILE
# or $HOME/.rnd. If neither exists, the pseudo random number generator will
# be initialized and a warning will be issued.
# Values: 0=only seed from /dev/[u]random, 1=also seed from weak randomness
#allow_weak_random_seed=1
# INCLUDE CONFIG FILE
# This directive allows you to include definitions from an external config file.
#include=<somefile.cfg>
# INCLUDE CONFIG DIRECTORY
# This directive allows you to include definitions from config files (with a
# .cfg extension) in one or more directories (with recursion).
#include_dir=<somedirectory>
#include_dir=<someotherdirectory>
# COMMAND DEFINITIONS
# Command definitions that this daemon will run. Definitions
# are in the following format:
#
# command[<command_name>]=<command_line>
#
# When the daemon receives a request to return the results of <command_name>
# it will execute the command specified by the <command_line> argument.
#
# Unlike Nagios, the command line cannot contain macros - it must be
# typed exactly as it should be executed.
#
# Note: Any plugins that are used in the command lines must reside
# on the machine that this daemon is running on! The examples below
# assume that you have plugins installed in a /usr/local/nagios/libexec
# directory. Also note that you will have to modify the definitions below
# to match the argument format the plugins expect. Remember, these are
# examples only!
# The following examples use hardcoded command arguments...
command[check_users]=/usr/local/nagios/libexec/check_users -w 5 -c 10
command[check_load]=/usr/local/nagios/libexec/check_load -w 15,10,5 -c 30,25,20
command[check_hda1]=/usr/local/nagios/libexec/check_disk -w 20% -c 10% -p /dev/hda1
command[check_zombie_procs]=/usr/local/nagios/libexec/check_procs -w 5 -c 10 -s Z
command[check_total_procs]=/usr/local/nagios/libexec/check_procs -w 150 -c 200
# The following examples allow user-supplied arguments and can
# only be used if the NRPE daemon was compiled with support for
# command arguments *AND* the dont_blame_nrpe directive in this
# config file is set to '1'. This poses a potential security risk, so
# make sure you read the SECURITY file before doing this.
#command[check_users]=/usr/local/nagios/libexec/check_users -w $ARG1$ -c $ARG2$
#command[check_load]=/usr/local/nagios/libexec/check_load -w $ARG1$ -c $ARG2$
#command[check_disk]=/usr/local/nagios/libexec/check_disk -w $ARG1$ -c $ARG2$ -p $ARG3$
#command[check_procs]=/usr/local/nagios/libexec/check_procs -w $ARG1$ -c $ARG2$ -s $ARG3$
command[check_opt]=/usr/local/nagios/bin/check_fs.sh -w 90 -c 92 -f /opt
command[check_home]=/usr/local/nagios/bin/check_fs.sh -w 80 -c 85 -f /home
command[check_var]=/usr/local/nagios/bin/check_fs.sh -w 80 -c 85 -f /var
command[check_usr]=/usr/local/nagios/bin/check_fs.sh -w 80 -c 85 -f /usr
command[check_vacio]=/usr/local/nagios/bin/check_fs.sh -w 80 -c 85 -f /
command[check_tmp]=/usr/local/nagios/bin/check_fs.sh -w 80 -c 85 -f /tmp
command[check_oracle]=/usr/local/nagios/bin/check_fs.sh -w 80 -c 85 -f /opt/oracle
command[check_boot]=/usr/local/nagios/bin/check_fs.sh -w 80 -c 85 -f /boot
command[check_servidor_CAS1]=/usr/local/nagios/bin/monitor_servers.sh CAS1
command[check_servidor_embargo1]=/usr/local/nagios/bin/monitor_servers.sh embargo1
command[check_servidor_srn1]=/usr/local/nagios/bin/monitor_servers.sh srn1
command[check_servidor_middleware_batch1]=/usr/local/nagios/bin/monitor_servers.sh middleware_batch1
command[check_servidor_middleware1]=/usr/local/nagios/bin/monitor_servers.sh middleware1
command[check_servidor_websvc_batch1]=/usr/local/nagios/bin/monitor_servers.sh websvc_batch1
command[check_servidor_websvc_crit1]=/usr/local/nagios/bin/monitor_servers.sh websvc_crit1
command[check_servidor_auxiliar1]=/usr/local/nagios/bin/monitor_servers.sh auxiliar1
command[check_servidor_websvc1]=/usr/local/nagios/bin/monitor_servers.sh websvc1
command[check_servidor_ALBPMServer1]=/usr/local/nagios/bin/monitor_servers.sh ALBPMServer1
command[check_servidor_rr_server]=/usr/local/nagios/bin/monitor_servers.sh rr_server
command[check_servidor_openfinance2]=/usr/local/nagios/bin/monitor_servers.sh openfinance2
command[check_servidor_AMLApps]=/usr/local/nagios/bin/monitor_servers.sh AMLApps
command[check_WLADMIN_MIDDLE]=/usr/local/nagios/bin/monitor_servers.sh WLADMIN_MIDDLE
command[check_WLADMIN_OFICINA]=/usr/local/nagios/bin/monitor_servers.sh WLADMIN_OFICINA_MIG
command[check_servidor_osb_server1]=/usr/local/nagios/bin/monitor_servers.sh osb_server1
command[check_WL_OSBBATCH_SERVER1]=/usr/local/nagios/bin/monitor_servers.sh osbbatch_server1
command[check_adap_B_PUBLICACION]=/usr/local/nagios/bin/check_ADAP.sh B_PUBLICACION
command[check_adap_B_DIFERIDA]=/usr/local/nagios/bin/check_ADAP.sh B_DIFERIDA
command[check_adap_B_QINVERSIS]=/usr/local/nagios/bin/check_ADAP.sh B_QINVERSIS
command[check_adap_B_QBATCH]=/usr/local/nagios/bin/check_ADAP.sh B_QBATCH
command[check_adap_B_QINTERNACIONAL]=/usr/local/nagios/bin/check_ADAP.sh B_QINTERNACIONAL
command[check_adap_B_QSALOMON]=/usr/local/nagios/bin/check_ADAP.sh B_QSALOMON
command[check_adap_B_QDERIVADOS]=/usr/local/nagios/bin/check_ADAP.sh B_QDERIVADOS
command[check_adap_B_QDER_ROUT_INT]=/usr/local/nagios/bin/check_ADAP.sh B_QDER_ROUT_INT
command[check_adap_B_QDER_MEFF_LIQUI]=/usr/local/nagios/bin/check_ADAP.sh B_QDER_MEFF_LIQUI
command[check_adap_B_QMEFF_CONT_FIX5]=/usr/local/nagios/bin/check_ADAP.sh B_QMEFF_CONT_FIX5
command[check_adap_B_QALERTAS]=/usr/local/nagios/bin/check_ADAP.sh B_QALERTAS
command[check_adap_B_QBLOOMBERG]=/usr/local/nagios/bin/check_ADAP.sh B_QBLOOMBERG
command[check_adap_B_QRENTABILIDAD]=/usr/local/nagios/bin/check_ADAP.sh B_QRENTABILIDAD
command[check_adap_B_QINTERDIRECTO]=/usr/local/nagios/bin/check_ADAP.sh B_QINTERDIRECTO
command[check_adap_B_DIFERIDA2]=/usr/local/nagios/bin/check_ADAP.sh B_DIFERIDA2
command[check_adap_B_QXGEN_ENT]=/usr/local/nagios/bin/check_ADAP.sh B_QXGEN_ENT
command[check_adap_B_QVTRADER44]=/usr/local/nagios/bin/check_ADAP.sh B_QVTRADER44
command[check_adap_B_QREBALANCEO]=/usr/local/nagios/bin/check_ADAP.sh B_QREBALANCEO
command[check_adap_B_NOMURA]=/usr/local/nagios/bin/check_ADAP.sh B_NOMURA
command[check_adap_B_CITI]=/usr/local/nagios/bin/check_ADAP.sh B_CITI
command[check_adap_B_QNOMURANAC]=/usr/local/nagios/bin/check_ADAP.sh B_QNOMURANAC
command[check_adap_B_QSMARTGATEFIX5]=/usr/local/nagios/bin/check_ADAP.sh B_QSMARTGATEFIX5
command[check_adap_B_QSMARTGATEETFSFIX5]=/usr/local/nagios/bin/check_ADAP.sh B_QSMARTGATEETFSFIX5
command[check_adap_B_QACCIONES]=/usr/local/nagios/bin/check_ADAP.sh B_QACCIONES
command[check_adap_B_QACCIONESPROF]=/usr/local/nagios/bin/check_ADAP.sh B_QACCIONESPROF
command[check_adap_B_QLATIBEX]=/usr/local/nagios/bin/check_ADAP.sh B_QLATIBEX
command[check_adap_B_QGESTORAS]=/usr/local/nagios/bin/check_ADAP.sh B_QGESTORAS
command[check_adap_B_QMAB]=/usr/local/nagios/bin/check_ADAP.sh B_QMAB
command[check_adap_B_GESCOLAS]=/usr/local/nagios/bin/check_ADAP.sh B_GESCOLAS
command[check_adap_B_INTEMBSWIF_LIQ]=/usr/local/nagios/bin/check_ADAP.sh B_INTEMBSWIF_LIQ
command[check_adap_B_INTEMBSWIF_TRAS]=/usr/local/nagios/bin/check_ADAP.sh B_INTEMBSWIF_TRAS
command[check_adap_B_INTEMBSWIF_RF]=/usr/local/nagios/bin/check_ADAP.sh B_INTEMBSWIF_RF
command[check_adap_B_INTEMBSWIF_SAL]=/usr/local/nagios/bin/check_ADAP.sh B_INTEMBSWIF_SAL
command[check_adap_B_QBATCH_XML]=/usr/local/nagios/bin/check_ADAP.sh B_QBATCH_XML
command[check_adap_B_EMAIL_XML]=/usr/local/nagios/bin/check_ADAP.sh B_EMAIL_XML
command[check_adap_B_BACKOFFICE]=/usr/local/nagios/bin/check_ADAP.sh B_BACKOFFICE
command[check_adap_B_BACKCRIT]=/usr/local/nagios/bin/check_ADAP.sh B_BACKCRIT
command[check_adap_B_BACKOFFICE_BLOOMBERG]=/usr/local/nagios/bin/check_ADAP.sh B_BACKOFFICE_BLOOMBERG
command[check_adap_B_BACKOFFICEWS]=/usr/local/nagios/bin/check_ADAP.sh B_BACKOFFICEWS
command[check_adap_B_RRS_BACKOFFICE]=/usr/local/nagios/bin/check_ADAP.sh B_RRS_BACKOFFICE
command[check_adap_B_BACKOFFICE_NOMURANAC]=/usr/local/nagios/bin/check_ADAP.sh B_BACKOFFICE_NOMURANAC
command[check_adap_B_BACKOFFICE_CERT_WS]=/usr/local/nagios/bin/check_ADAP.sh B_BACKOFFICE_CERT_WS
command[check_adap_B_BACKOFFICE_BATCHWS]=/usr/local/nagios/bin/check_ADAP.sh B_BACKOFFICE_BATCHWS
command[check_adap_B_MULTIHERRAMIENTA]=/usr/local/nagios/bin/check_ADAP.sh B_MULTIHERRAMIENTA
command[check_adap_MULHILO_PROC_GEN]=/usr/local/nagios/bin/check_ADAP.sh MULHILO_PROC_GEN
command[check_adap_B_ADAPT_MULTIPUB]=/usr/local/nagios/bin/check_proc_MULTIPUB.sh
command[check_adap_B_ADPTFIX]=/usr/local/nagios/bin/check_ADAP.sh B_ADPTFIX
command[check_adap_B_ADPTFIX_ACC]=/usr/local/nagios/bin/check_ADAP.sh B_ADPTFIX_ACC
command[check_adap_B_ADPTFIX_ACC_PROF]=/usr/local/nagios/bin/check_ADAP.sh B_ADPTFIX_ACC_PROF
command[check_adap_B_ADPTFIX_DERIVADOS]=/usr/local/nagios/bin/check_ADAP.sh B_ADPTFIX_DERIVADOS
command[check_adap_B_ADPTFIX_RVI]=/usr/local/nagios/bin/check_ADAP.sh B_ADPTFIX_RVI
command[check_adap_B_ADPTFIX_VT]=/usr/local/nagios/bin/check_ADAPinverso.sh ADPTFIX_VT
command[check_adap_B_CONTENIDOS]=/usr/local/nagios/bin/check_ADAP.sh B_CONTENIDOS
command[check_adap_B_SQL_SERVER]=/usr/local/nagios/bin/check_ADAP.sh B_SQL_SERVER
command[check_adap_B_MENSAJERIA]=/usr/local/nagios/bin/check_ADAP.sh B_MENSAJERIA
command[check_adap_B_ADPTALERTAS]=/usr/local/nagios/bin/check_ADAP.sh B_ADPTALERTAS
command[check_adap_B_DISPARO]=/usr/local/nagios/bin/check_ADAP.sh B_DISPARO
command[check_adap_B_DISPARO_TS]=/usr/local/nagios/bin/check_ADAP.sh B_DISPARO_TS
command[check_adap_BLOOMBERG_ORDEN]=/usr/local/nagios/bin/check_ADAP.sh BLOOMBERG_ORDEN
command[check_adap_BLOOMBERG_EJEC]=/usr/local/nagios/bin/check_ADAP.sh BLOOMBERG_EJEC
command[check_adap_B_GESENVIOS]=/usr/local/nagios/bin/check_ADAP.sh B_GESENVIOS
command[check_adap_RoutNomuranacOrden]=/usr/local/nagios/bin/check_ADAP.sh RoutNomuranacOrden
command[check_adap_FQPublicacion]=/usr/local/nagios/bin/check_ADAP.sh FQPublicacion
command[check_adap_CONS_FIE]=/usr/local/nagios/bin/check_ADAP.sh CONS_FIE
command[check_adap_RoutNomuranacEjec]=/usr/local/nagios/bin/check_ADAP.sh RoutNomuranacEjec
command[check_adap_MULHILO_PROC_GEN]=/usr/local/nagios/bin/check_ADAP.sh MULHILO_PROC_GEN
command[check_adap_B_ADPTFIX_DERIINT]=/usr/local/nagios/bin/check_ADAP.sh B_ADPTFIX_DERIINT
command[check_adap_B_SEDA]=/usr/local/nagios/bin/check_ADAP.sh B_SEDA
command[check_BACKPESADOS]=/usr/local/nagios/bin/check_ADAP.sh B_BACKPESADOS
command[check_NodeManager_OSB]=/usr/local/nagios/libexec/check_OSBNode.sh
command[check_Admin_OSB]=/usr/local/nagios/libexec/check_OSBADMIN.sh
command[check_Admin_OSBBATCH]=/usr/local/nagios/libexec/check_OSBBATCHADMIN.sh
#command[check_var]=/usr/local/nagios/bin/monitor_owner.sh /var/tmp/ledgers ets ets
#command[check_FIX]=/usr/local/nagios/bin/monitor_owner.sh /var/tmp/ledgers/FIX ets ets
#command[check_ALERTAS]=/usr/local/nagios/bin/monitor_owner.sh /var/tmp/ledgers/BANCO/ALERTAS ets ets
#command[check_InterDirecto]=/usr/local/nagios/bin/monitor_owner.sh /var/tmp/ledgers/InterDirecto ets ets
command[check_logs]=/usr/local/nagios/bin/monitor_owner.sh /opt/inversis/logs ets ets
command[check_pids]=/usr/local/nagios/bin/monitor_owner.sh /opt/inversis/pids ets ets
command[check_ledgers]=/usr/local/nagios/bin/monitor_owner.sh /opt/inversis/ledgers ets ets
command[check_BEA10]=/usr/local/nagios/bin/monitor_owner.sh /opt/BEA10 ets ets
##############
##Comentamos el script de check_logfiles.sh y lo modificamos por la ejecucion del perl directamente
##############
#command[check_correlacion]=/usr/local/nagios/bin/check_correlacion_logs.sh $ARG1$ "$ARG2$"
###command[check_logs_correlacion]=/usr/local/nagios/libexec/check_logfiles.sh $ARG1$ "$ARG2$"
#command[check_owner_ets]=/usr/local/nagios/libexec/monitor_PROCESOS_OWNER_ets.sh $ARG1$
command[check_owner_root]=/usr/local/nagios/libexec/monitor_PROCESOS_OWNER_root.sh $ARG1$
command[check_fich_etc]=/usr/local/nagios/libexec/check_mod_fich_etc.sh
command[check_fich_usr]=/usr/local/nagios/libexec/check_mod_fich_usr.sh
command[check_cpu_estado]=/usr/local/nagios/libexec/check_cpu_stats.sh
command[check_mem]=/usr/local/nagios/libexec/check_mem.sh -w 18 -c 15 -p
command[check_proc_xinetd]=/usr/local/nagios/libexec/check_ps.sh -p xinetd
command[check_log1]=perl /usr/local/nagios/libexec/check_logfiles --tag="failed_new_thread" --logfile=/opt/BEA10/user_projects/domains/MIDDLE/servers/embargo1/logs/access.log --criticalpattern="failed to start new thread"
command[check_log2]=perl /usr/local/nagios/libexec/check_logfiles --tag="XadapterException_99970" --logfile=/opt/inversis/BANCO/ADAPT_BANCO/logs/COMUNICACIONESXGEN_ENT_99970.log --criticalpattern="XadpterException"
command[check_log3]=perl /usr/local/nagios/libexec/check_logfiles --tag="XadapterException_99971" --logfile=/opt/inversis/BANCO/ADAPT_BANCO/logs/COMUNICACIONESXGEN_ENT_99971.log --criticalpattern="XadpterException"
command[check_log4]=perl /usr/local/nagios/libexec/check_logfiles --tag="XadapterException_99972" --logfile=/opt/inversis/BANCO/ADAPT_BANCO/logs/COMUNICACIONESXGEN_ENT_99972.log --criticalpattern="XadpterException"
command[check_log5]=perl /usr/local/nagios/libexec/check_logfiles --tag="XadapterException_99973" --logfile=/opt/inversis/BANCO/ADAPT_BANCO/logs/COMUNICACIONESXGEN_ENT_99973.log --criticalpattern="XadpterException"
command[check_log6]=perl /usr/local/nagios/libexec/check_logfiles --tag="XadapterException_99974" --logfile=/opt/inversis/BANCO/ADAPT_BANCO/logs/COMUNICACIONESXGEN_ENT_99974.log --criticalpattern="XadpterException"
command[check_log7]=perl /usr/local/nagios/libexec/check_logfiles --tag="failed_thread" --logfile=/opt/BEA10/user_projects/domains/MIDDLE/servers/embargo1/logs/embargo1.out --criticalpattern="failed to start new thread"
#command[check_log8]=perl /usr/local/nagios/libexec/check_logfiles --tag="instances_from_engine" --logfile=/opt/BEA10/user_projects/domains/MIDDLE/servers/esb2/logs/esb2.out --criticalpattern="Cannot retrieve instances from engine"
command[check_log9]=perl /usr/local/nagios/libexec/check_logfiles --tag="ws_documentum_error" --logfile=/opt/inversis/logs/BANCO/GENERAL_SERVICES/FIRMADIG/firmadigWEB.log --criticalpattern="LLAMADA AL WS DE DOCUMENTUM FINALIZADA CON ERROR"
command[check_log10]=perl /usr/local/nagios/libexec/check_logfiles --tag="mqexception" --logfile=/opt/inversis/BANCO/WEBSVC/INTEMBSWIF/logs/intembswif.log --criticalpattern="com.ibm.mq.MQException: Completion Code"
command[check_log11]=perl /usr/local/nagios/libexec/check_logfiles --tag="error_crear_transporte" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ERROR AL CREAR EL TRANSPORTE"
command[check_log12]=perl /usr/local/nagios/libexec/check_logfiles --tag="wsembargos_500" --logfile=/opt/BEA10/user_projects/domains/MIDDLE/servers/embargo1/logs/access.log --criticalpattern="POST /WS-CGPJ/services/WSEmbargos HTTP/1.0 500"
command[check_log13]=perl /usr/local/nagios/libexec/check_logfiles --tag="error_al_desencolar" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ERROR AL DESENCOLAR"
command[check_log14]=perl /usr/local/nagios/libexec/check_logfiles --tag="error_critico" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ERROR CRITICO"
command[check_log15]=perl /usr/local/nagios/libexec/check_logfiles --tag="error_establecer" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="Error no se pudo establecer"
command[check_log16]=perl /usr/local/nagios/libexec/check_logfiles --tag="errores_generales" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="Errores Generales"
command[check_log17]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_00020" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-00020"
command[check_log18]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_00257" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-00257"
command[check_log19]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_00600" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-00600"
command[check_log20]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_00604" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-00604"
command[check_log21]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_01000" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-01000"
command[check_log22]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_01089" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-01089"
command[check_log23]=perl /usr/local/nagios/libexec/check_logfiles --tag="tpcall" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/backoffice_0.log --criticalpattern="Al hacer el Tpcall"
command[check_log24]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_01114" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-01114"
command[check_log25]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_01146" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-01146"
command[check_log26]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_04301" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-04031"
command[check_log27]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_16009" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-16009"
command[check_log28]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_16055" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-16055"
command[check_log29]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_1563" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-1653"
command[check_log30]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_1654" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-1654"
command[check_log31]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_20001" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-20001"
command[check_log32]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_28575" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-28575"
command[check_log33]=perl /usr/local/nagios/libexec/check_logfiles --tag="ora_29701" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/PUBLICACION_44923.log --criticalpattern="ORA-29701"
command[check_log34]=perl /usr/local/nagios/libexec/check_logfiles --tag="error_transporte" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/backoffice_0.log --criticalpattern="ERROR AL CREAR EL TRANSPORTE"
command[check_log35]=perl /usr/local/nagios/libexec/check_logfiles --tag="error_obteniendo" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/backoffice_0.log --criticalpattern="etconexion:Error obteniendo conexi"
command[check_log36]=perl /usr/local/nagios/libexec/check_logfiles --tag="repetition_alert" --logfile=/opt/inversis/MARCABLANCA/CJMAR_44923/logs/backoffice_0.log --criticalpattern="REPETITION_ALERT"
command[check_log37]=perl /usr/local/nagios/libexec/check_logfiles --tag="warning_db_cache" --logfile=/opt/inversis/BANCO/ADAPT_BANCO/logs/backoffice_0.log --criticalpattern="WARNING_DB_CACHE_USAGE"
command[check_log38]=perl /usr/local/nagios/libexec/check_logfiles --tag="warning_dispatcher" --logfile=/opt/inversis/BANCO/ADAPT_BANCO/logs/backoffice_0.log --criticalpattern="WARNING_DISPATCHER_USAGE"
command[check_log39]=perl /usr/local/nagios/libexec/check_logfiles --tag="XadapterException_99969" --logfile=/opt/inversis/BANCO/ADAPT_BANCO/logs/COMUNICACIONESXGEN_ENT_99969.log --criticalpattern="XadpterException"
command[check_log40]=perl /usr/local/nagios/libexec/check_logfiles --tag="exception" --logfile=/opt/inversis/BANCO/SSO/logs/logHttpBridgeSSO.log --criticalpattern="Exception"
command[check_log41]=perl /usr/local/nagios/libexec/check_logfiles --tag="outofmemory" --logfile=/opt/BEA10/user_projects/domains/MIDDLE/servers/CAS1/logs/CAS1.log --criticalpattern="OutOfMemoryError"
command[check_log42]=perl /usr/local/nagios/libexec/check_logfiles --tag="error_general" --logfile=/opt/OSB_11.1.1.7.0/user_projects/domains/OSB_PROD/servers/osb_server1/logs/osb_server1.log --criticalpattern="SE HA PRODUCIDO UN ERROR GENERAL"
#Monitorizacion del numero de terminales recuperados en OSB
command[check_log43]=perl /usr/local/nagios/libexec/check_logfiles --tag="recuperaron_terminales" --logfile=/opt/OSB_11.1.1.7.0/user_projects/domains/OSB_PROD/servers/osb_server1/logs/osb_server1.out --criticalpattern="Se recuperaron 0 terminales"
#Monitorizacion para chequear cuando se pasa el terminal financiero a nulo
command[check_log44]=perl /usr/local/nagios/libexec/check_logfiles --tag="financiero_nulo" --logfile=/opt/OSB_11.1.1.7.0/user_projects/domains/OSB_PROD/servers/osb_server1/logs/osb_server1.out --criticalpattern="SE PASA EL SERVIDOR FINANCIERO A NULO en borrowTerminal"
#Monitorizacion para chequear cuando se pasa el terminal financiero a nulo
command[check_log45]=perl /usr/local/nagios/libexec/check_logfiles --tag="returnterminal_nulo" --logfile=/opt/OSB_11.1.1.7.0/user_projects/domains/OSB_PROD/servers/osb_server1/logs/osb_server1.out --criticalpattern="SE PASA EL SERVIDOR FINANCIERO returnTerminal A NULO"
#Monitorizacion de los terminales disponibles para oficina
command[check_log46]=perl /usr/local/nagios/libexec/check_logfiles --tag="terminales_disponibles" --logfile=/opt/OSB_11.1.1.7.0/user_projects/domains/OSB_PROD/servers/osb_server1/logs/osb_server1.log --criticalpattern="NO HAY TERMINALES DISPONIBLES PARA ESA OFICINA"
#Monitorizacion de los servicios donde no se esta informando el nodo servidor financiero
command[check_log47]=perl /usr/local/nagios/libexec/check_logfiles --tag="informado_servidor" --logfile=/opt/OSB_11.1.1.7.0/user_projects/domains/OSB_PROD/servers/osb_server1/logs/osb_server1.log --criticalpattern="NO SE HA INFORMADO EL NODO SERVIDOR FINANCIERO"
#Monitorizacion cuando se ha alcanzado el numero maximo de threads del WatchManagerEvents
command[check_log48]=perl /usr/local/nagios/libexec/check_logfiles --tag="watchmanagerevents" --logfile=/opt/OSB_11.1.1.7.0/user_projects/domains/OSB_PROD/servers/osb_server1/logs/osb_server1.out --criticalpattern="maximum thread constraint WatchManagerEvents is reached"
command[check_ERRORES_BEA]=/usr/local/nagios/libexec/Errores_BEA.sh
#Monitor de Tamano de fichero
command[check_file_osb_server1]=/usr/local/nagios/bin/check_file_size_V2.sh --maxwarn 1610612736 --maxcrit 2040109465 /opt/OSB_11.1.1.7.0/user_projects/domains/OSB_PROD/servers/osb_server1/logs/osb_server1.out
#Monitorizacion de tiempo de actualizacion de un fichero
command[check_osb_server_age]=/usr/local/nagios/libexec/check_fileage.py -f /opt/OSB_11.1.1.7.0/user_projects/domains/OSB_PROD/servers/osb_server1/logs/osb_server1.out -w 5 -c 7
#Monitorizacion de los servicios de Andbank
command[check_andbank_services]=/usr/local/nagios/libexec/monitorServiciosAndbank.sh
#Monitorizacion de las colas JMS de OSB
command[check_status_error_queue1_osb]=/usr/local/nagios/libexec/status_error_queue1_osb.sh
command[check_log49]=perl /usr/local/nagios/libexec/check_logfiles --tag="warning_tibco" --logfile=/opt/inversis/BANCO/ADAPT_BANCO/logs/backoffice_0.log --criticalpattern="WARNING_TIBCO_QUEUE"
command[check_log50]=perl /usr/local/nagios/libexec/check_logfiles --tag="system_resources" --logfile=/opt/inversis/BANCO/ALERTAS/logs/mensajeria.log --criticalpattern="452 4.3.1 Insufficient system resources"
command[check_log51]=perl /usr/local/nagios/libexec/check_logfiles --tag="check_log51" --logfile=/opt/BEA10/user_projects/domains/MIDDLE/servers/websvc_crit1/logs/websvc_crit1.out --criticalpattern="OutOfMemoryError"
#Monitorizacion para saber cuando se reinicia el servidor websvc_crit1
command[check_log52]=perl /usr/local/nagios/libexec/check_logfiles --tag="check_log52" --logfile=/opt/BEA10/user_projects/domains/MIDDLE/servers/websvc_crit1/logs/websvc_crit1.out --criticalpattern="Server state changed to STARTING"
command[check_ntp]=/usr/local/nagios/libexec/check_ntp_time -H 192.168.247.150 -w 30 -c 60
#MOnitorizacion de operaciones que no se vuelcan en la consola de errores
command[check_log78]=perl /usr/local/nagios/libexec/check_logfiles --tag="check_log78" --logfile=/opt/inversis/BANCO/WEBSVC/CONSOLAERRORMB/logs/consolaerrormb.log --criticalpattern="not-null property references a null or transient value"
#Chequeos de mensajes en colas JMS para mensajeria de ordenes
command[check_status_error_queue1_abmensaordenes_osb]=/usr/local/nagios/libexec/status_error_queue1_abmensaordenes_osb.sh
#Chequeos para el adaptador backpesados
command[check_log79]=perl /usr/local/nagios/libexec/check_logfiles --tag="check_log79" --logfile=/opt/inversis/BANCO/ADAPT_BANCO/logs/backpesados_0.log --criticalpattern="WARNING_DB_CACHE_USAGE"
command[check_log80]=perl /usr/local/nagios/libexec/check_logfiles --tag="check_log80" --logfile=/opt/inversis/BANCO/ADAPT_BANCO/logs/backpesados_0.log --criticalpattern="WARNING_DISPATCHER_USAGE"
command[check_log81]=perl /usr/local/nagios/libexec/check_logfiles --tag="check_log81" --logfile=/opt/inversis/BANCO/ADAPT_BANCO/logs/backpesados_0.log --criticalpattern="WARNING_TIBCO_QUEUE"
command[check_log82]=perl /usr/local/nagios/libexec/check_logfiles --tag="errorPorExcepcion" --logfile=/opt/inversis/logs/BANCO/ALERTAS/alertas.log --criticalpattern="ERROR POR EXCEPCION"
/usr/local/nagios/libexec/check_nrpe -H 192.168.246.174
NRPE v2.14
nmap <client ip> -p 5666
nmap 192.168.246.174 -p 5666
Starting Nmap 4.11 (
http://www.insecure.org/nmap/ ) at 2015-10-26 11:07 CET
Interesting ports on prometeo-bp.inversis.com (192.168.246.174):
PORT STATE SERVICE
5666/tcp open unknown
Nmap finished: 1 IP address (1 host up) scanned in 0.141 seconds
Re: service check timeouts
Posted: Thu Nov 05, 2015 10:53 am
by rkennedy
Is your IP statically set on the Nagios server or is it using DHCP? Does it have multiple NIC interfaces in use?
Do you perhaps have an old version of NRPE still running in the background that would cause the intermittent results?
Can you post a copy of your /usr/local/nagios/etc/nrpe.cfg for us to look at?