Monitor Netapp device which is using SNMP V3

[tgriep]

The second script with the missing arguments message, It looks like you have to use a capital SHA1 for the protocol.

Code: Select all

-a, --authproto authentication protocol (MD5 or SHA1)

Try this and see if it works.

Code: Select all

./check_netapp.pl -H 192.168.23.45 -C public -P 3 -L authPriv -U myuser -a SHA1 -A mypassword -X mypassword -v DISKUSED -o /vol/vol0/ -w 60 -c 70 -t 60

[arunkrishnan.tvm]

I have tried the below command but still getting the "Missing arguments!" error.

Code: Select all

./check_netapp.pl -H 192.168.23.45 -C public -P 3 -L authPriv -U myuser -a SHA1 -A mypassword -X mypassword -v DISKUSED -o /vol/vol0/ -w 60 -c 70 -t 60

[rkennedy]

There could be an if statement that is checking for a 1 or 2c, which means you'll need to modify the perl script even further.

As it's custom plugin, we're limited on the support we can provide. The plugin will need to be updated for full SNMPv3 support.

[arunkrishnan.tvm]

Ok, so I have to just change 2c to 3c in the below if statements, right?

Code: Select all

if( ($opt{'check_type'} eq 'ISCSIOPS') or ($opt{'check_type'} eq 'FCPOPS') ) {
        $opt{'version'} = '2c';
}

if ($opt{'version'} eq '2c') {
                                $used = _get_oid_value($snmp_session,"$snmp_netapp_volume_id_table_df64_used.$oid");
                                $capacity = _get_oid_value($snmp_session,"$snmp_netapp_volume_id_table_df64_total.$oid");
                        }

Also what about check command parameters for (username, authprotocol, authpassword, privprotocol, privpassword) ? What letter should I use to call these variables ?

[Box293]

Have a look at the plugin /user/local/nagios/libexec/check_snmp_process.pl as it has all the parameters.

You should be able to use that code example to define the opt arguments etc.

[arunkrishnan.tvm]

Sorry, I have failed to modify the Perl script using the required variables.

Finally found one another plugin in Nagios Exchange with SNMP3 support. When I execute the check command like below I am getting incorrect argument error.
Please help me to correct the command:

https://exchange.nagios.org/directory/P ... p3/details

./check_netapp3.pl -H 192.168.23.4 -P 3 -L authpriv -U myusr -a SHA1 -A mypasswd -X mypasswd -v CPULOAD -w 60 -c 70

[arunkrishnan.tvm]

Following is the error I am getting

Code: Select all

Missing or incorrect arguments!

  (SNMP v1, v2c)
  ./check_netapp3.pl -H ip_address -v variable
      [ -P snmp_version ] [ -c community ] [ -p port_number ]

  (SNMP v3)
  ./check_netapp3.pl -H ip_address -v variable -L sec_level -U sec_name
      [ -w warn_range ]  [ -c crit_range ]  [ -c community ] [ -t timeout ]
      [ -p port_number ] [ -P 3 ] [ -a auth_proto ]
      [ -A auth_passwd ] [ -X priv_passwd ] [-o volume ]

[arunkrishnan.tvm]

Any help please ?

[hsmith]

Bumping your post will not result in a quicker response time. With that being said, does your username or password have any special characters in it that may be messing the syntax up?

[tmcdonald]

Any help please ?

Please be patient - 20 minutes is not a long time to wait for an answer.

Check the case-sensitivity of the authpriv string you use - looking into the source code it might need to be authPriv with a capital P.