Monitor Switches

[jwu]

I went through the threads and tried the solutions in the past, I'm not successful at this point
setup and received error message as attached
1. I have a Cisco Switch
2. I'm using the Network Switch / Router monitoring wizard
3. IP is pingable
[root@cvglobal ~]# ping 71.40.44.249
PING 71.40.44.249 (71.40.44.249) 56(84) bytes of data.
64 bytes from 71.40.44.249: icmp_seq=1 ttl=244 time=44.2 ms
64 bytes from 71.40.44.249: icmp_seq=2 ttl=244 time=42.0 ms
64 bytes from 71.40.44.249: icmp_seq=3 ttl=244 time=39.6 ms
64 bytes from 71.40.44.249: icmp_seq=4 ttl=244 time=33.8 ms
--- 71.40.44.249 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3639ms
rtt min/avg/max/mdev = 33.875/39.976/44.286/3.886 ms

4. SNMP enabled
[root@cvglobal ~]# nmap -p 161 -sU 71.40.44.249

Starting Nmap 5.51 ( http://nmap.org ) at 2013-08-06 10:53 EDT
Nmap scan report for 71.40.44.249
Host is up (0.046s latency).
PORT STATE SERVICE
161/udp open snmp

5. [root@cvglobal ~]# snmpwalk -H 71.40.44.249 -c wipro -v1
No log handling enabled - turning on stderr logging
Did not find 'zeroDotZero' in module SNMPv2-SMI (/usr/share/snmp/mibs/IP-MIB.txt)
Did not find 'zeroDotZero' in module SNMPv2-SMI (/usr/share/snmp/mibs/DISMAN-EVENT-MIB.txt)
Did not find 'zeroDotZero' in module SNMPv2-SMI (/usr/share/snmp/mibs/DISMAN-SCHEDULE-MIB.txt)
Configuration directives understood:
In snmpwalk.conf and snmpwalk.local.conf:
includeRequested (1|yes|true|0|no|false)
excludeRequested (1|yes|true|0|no|false)
printStatistics (1|yes|true|0|no|false)
dontCheckOrdering (1|yes|true|0|no|false)
timeResults (1|yes|true|0|no|false)
In snmp.conf and snmp.local.conf:
alias NAME TRANSPORT_DEFINITION
doDebugging (1|0)
debugTokens token[,token...]
logTimestamp (1|yes|true|0|no|false)
mibdirs [mib-dirs|+mib-dirs|-mib-dirs]
mibs [mib-tokens|+mib-tokens]
mibfile mibfile-to-read
showMibErrors (1|yes|true|0|no|false)
commentToEOL (1|yes|true|0|no|false)
strictCommentTerm (1|yes|true|0|no|false)
mibAllowUnderline (1|yes|true|0|no|false)
mibWarningLevel integerValue
mibReplaceWithLatest (1|yes|true|0|no|false)
printNumericEnums (1|yes|true|0|no|false)
printNumericOids (1|yes|true|0|no|false)
escapeQuotes (1|yes|true|0|no|false)
dontBreakdownOids (1|yes|true|0|no|false)
quickPrinting (1|yes|true|0|no|false)
numericTimeticks (1|yes|true|0|no|false)
oidOutputFormat integerValue
suffixPrinting integerValue
extendedIndex (1|yes|true|0|no|false)
printHexText (1|yes|true|0|no|false)
printValueOnly (1|yes|true|0|no|false)
dontPrintUnits (1|yes|true|0|no|false)
hexOutputLength integerValue
dumpPacket (1|yes|true|0|no|false)
reverseEncodeBER (1|yes|true|0|no|false)
defaultPort integerValue
defCommunity string
noTokenWarnings (1|yes|true|0|no|false)
noRangeCheck (1|yes|true|0|no|false)
persistentDir string
tempFilePattern string
noDisplayHint (1|yes|true|0|no|false)
16bitIDs (1|yes|true|0|no|false)
clientaddr string
clientaddrUsesPort (1|yes|true|0|no|false)
serverSendBuf integerValue
serverRecvBuf integerValue
clientSendBuf integerValue
clientRecvBuf integerValue
noPersistentLoad (1|yes|true|0|no|false)
noPersistentSave (1|yes|true|0|no|false)
noContextEngineIDDiscovery (1|yes|true|0|no|false)
defDomain application domain
defTarget application domain target
defSecurityModel string
defSecurityName string
defContext string
defPassphrase string
defAuthPassphrase string
defPrivPassphrase string
defAuthMasterKey string
defPrivMasterKey string
defAuthLocalizedKey string
defPrivLocalizedKey string
defVersion 1|2c|3
defAuthType MD5|SHA
defPrivType DES|AES
defSecurityLevel noAuthNoPriv|authNoPriv|authPriv
In snmpapp.conf and snmpapp.local.conf:
defDomain application domain
defTarget application domain target
engineID string
engineIDType num
engineIDNic string

5. I'm not able to do full walk
[root@cvglobal ~]# snmpwalk -v1 -c wipro 71.40.44.249
No log handling enabled - turning on stderr logging
Did not find 'zeroDotZero' in module SNMPv2-SMI (/usr/share/snmp/mibs/IP-MIB.txt)
Did not find 'zeroDotZero' in module SNMPv2-SMI (/usr/share/snmp/mibs/DISMAN-EVENT-MIB.txt)
Did not find 'zeroDotZero' in module SNMPv2-SMI (/usr/share/snmp/mibs/DISMAN-SCHEDULE-MIB.txt)
Timeout: No Response from 71.40.44.249

[root@cvglobal ~]# snmpwalk -v1 -c wipro 71.40.44.249 1.3.6.1.2.1.2.2.1.8
No log handling enabled - turning on stderr logging
Did not find 'zeroDotZero' in module SNMPv2-SMI (/usr/share/snmp/mibs/IP-MIB.txt)
Did not find 'zeroDotZero' in module SNMPv2-SMI (/usr/share/snmp/mibs/DISMAN-EVENT-MIB.txt)
Did not find 'zeroDotZero' in module SNMPv2-SMI (/usr/share/snmp/mibs/DISMAN-SCHEDULE-MIB.txt)
Timeout: No Response from 71.40.44.249

[root@cvglobal ~]# snmptranslate -mALL 1.3.6.1.2.1.2.2.1.8
Did not find 'zeroDotZero' in module SNMPv2-SMI (/usr/share/snmp/mibs/IP-MIB.txt)
Did not find 'zeroDotZero' in module SNMPv2-SMI (/usr/share/snmp/mibs/DISMAN-EVENT-MIB.txt)
Did not find 'zeroDotZero' in module SNMPv2-SMI (/usr/share/snmp/mibs/DISMAN-SCHEDULE-MIB.txt)
IF-MIB::ifOperStatus


is there anything I need to turn on or enable?

[abrist]

Looks like you may be having some mib problems. What is the output of:

Code: Select all

grep -5 zeroDotZero /usr/share/snmp/mibs/*