SNMP data from IBM IMM

[fabric]

Hi everyone, I want to get the data displayed on the IBM IMM as temperature, voltage and so on via SNMP.
For example I ran the following command:

Code: Select all

snmpget -O n -v 2c -c public IP_address .1.3.6.1.4.1.2.3.51.3.1.1.2.1.1

where IP_address is the address of the IMM. I get

Code: Select all

Timeout: No response from 

Instead if IP_address is the server IP I get

Code: Select all

no such object available on this agent at this oid

Obviously the SNMP is active on both the IMM and the server.

I also tried the plugin check_snmp_ibm_imm

Code: Select all

./check_snmp_ibm_imm.sh -H IP -C public -T health

It answers again Timeout: No response, both using the server address or the IMM address.

Can anyone suggest me what is the right way to get this data and what could be wrong (SNMP configuration, firewall, anything else)?

Thank you very much.

[JLT]

If you have not configured SNMP on the IMM, try these steps:

Go to IMM Management > Network

Click "Enable SNMPv1".
Disable SNMPv3.
Enable SNMP traps

On the Communities tab:

Community name:
public
Access type: Get
Allow specific hosts:
Add host IP address.

On the Traps tab:
Select Critical and Attention events.

Then click Apply button.

[Box293]

Hi everyone, I want to get the data displayed on the IBM IMM as temperature, voltage and so on via SNMP.
For example I ran the following command:

Code: Select all

snmpget -O n -v 2c -c public IP_address .1.3.6.1.4.1.2.3.51.3.1.1.2.1.1

I learnt one thing at the Nagios World Conference this year and it was that OID's ending in .1 are tables and hence have a subnet of information.

What happens when you try and walk the device?

Code: Select all

snmpwalk -v 2c -c public IP_address -m all 1.3.6.1.4.1.2.3.51

[fabric]

What happens when you try and walk the device?

Code: Select all

snmpwalk -v 2c -c public IP_address -m all 1.3.6.1.4.1.2.3.51

I get

Code: Select all

IBM-SYSTEM-MIB::ibm.3.51 = No Such Object available on this agent at this OID

if IP_address is the server IP.

It seems that the OID is missing somewhere.

On the Traps tab:
Select Critical and Attention events.

about this, this IMM doesn't have a Trap tab (the server is an X3650 M2). The only similar option is in IMM Control > Alerts - SNMP Alerts Settings, where I can select the alerts that will be sent to SNMP among Critical, Warning and System alerts.

[tgriep]

Can you post your IBM-SYSTEM-MIB MIB file so we can review it?

[fabric]

Here is the file

[tgriep]

That MIB file doesn't contain the OID that you are checking for. I translated it and included it in the post. If the data that you are looking for isn't shown below, you may have to get a different MIB file that has it.

Code: Select all

"org"                   "1.3"
"dod"                   "1.3.6"
"internet"                      "1.3.6.1"
"directory"                     "1.3.6.1.1"
"mgmt"                  "1.3.6.1.2"
"experimental"                  "1.3.6.1.3"
"private"                       "1.3.6.1.4"
"enterprises"                   "1.3.6.1.4.1"
"ibm"                   "1.3.6.1.4.1.2"
"ibmProd"                       "1.3.6.1.4.1.2.6"
"ibmServer"                     "1.3.6.1.4.1.2.6.159"
"ibmSystemAgentVersion"                 "1.3.6.1.4.1.2.6.159.0"
"ibmSystem"                     "1.3.6.1.4.1.2.6.159.1"
"ibmSystemMIB"                  "1.3.6.1.4.1.2.6.159.1.1"
"ibmSystemTrap"                 "1.3.6.1.4.1.2.6.159.1.1.0"
"win32"                 "1.3.6.1.4.1.2.6.159.1.1.2"
"win32Event"                    "1.3.6.1.4.1.2.6.159.1.1.2.0"
"win32WMI"                      "1.3.6.1.4.1.2.6.159.1.1.2.10"
"win32SMBIOS"                   "1.3.6.1.4.1.2.6.159.1.1.2.20"
"ibmSystemAgent"                        "1.3.6.1.4.1.2.6.159.1.1.10"
"ibmSystemAgentUpObjs"                  "1.3.6.1.4.1.2.6.159.1.1.10.0"
"ibmSystemMgmtHwIPEndPointUp"                   "1.3.6.1.4.1.2.6.159.1.1.10.0.3"
"ibmSystemEventSubsystem"                       "1.3.6.1.4.1.2.6.159.1.1.20"
"ibmSystemHealth"                       "1.3.6.1.4.1.2.6.159.1.1.30"
"ibmSystemHealthUp"                     "1.3.6.1.4.1.2.6.159.1.1.30.0"
"ibmSystemStorageUp"                    "1.3.6.1.4.1.2.6.159.1.1.30.0.1"
"ibmSystemPhysicalDiskUp"                       "1.3.6.1.4.1.2.6.159.1.1.30.0.1.1"
"ibmSystemLogicalDiskUp"                        "1.3.6.1.4.1.2.6.159.1.1.30.0.1.2"
"ibmSystemVitalProductData"                     "1.3.6.1.4.1.2.6.159.1.1.40"
"ibmSystemSMART"                        "1.3.6.1.4.1.2.6.159.1.1.50"
"ibmSystemAssetID"                      "1.3.6.1.4.1.2.6.159.1.1.60"
"ibmSystemAlertOnLAN"                   "1.3.6.1.4.1.2.6.159.1.1.70"
"ibmSystemLMSensor"                     "1.3.6.1.4.1.2.6.159.1.1.80"
"ibmSystemLMSensorUp"                   "1.3.6.1.4.1.2.6.159.1.1.80.0"
"ibmSystemVoltageUp"                    "1.3.6.1.4.1.2.6.159.1.1.80.0.1"
"ibmSystemTemperatureUp"                        "1.3.6.1.4.1.2.6.159.1.1.80.0.2"
"ibmSystemTachometerUp"                 "1.3.6.1.4.1.2.6.159.1.1.80.0.3"
"ibmSystemITDirector"                   "1.3.6.1.4.1.2.6.159.1.1.90"
"ibmSystemSmbios"                       "1.3.6.1.4.1.2.6.159.1.1.100"
"ibmSystemNetwork"                      "1.3.6.1.4.1.2.6.159.1.1.110"
"ibmSystemNetworkUp"                    "1.3.6.1.4.1.2.6.159.1.1.110.0"
"ibmSystemMemory"                       "1.3.6.1.4.1.2.6.159.1.1.120"
"ibmSystemMemoryUp"                     "1.3.6.1.4.1.2.6.159.1.1.120.0"
"ibmSystemPower"                        "1.3.6.1.4.1.2.6.159.1.1.130"
"ibmSystemPowerUp"                      "1.3.6.1.4.1.2.6.159.1.1.130.0"
"ibmSystemProcessor"                    "1.3.6.1.4.1.2.6.159.1.1.140"
"ibmSystemProcessorUp"                  "1.3.6.1.4.1.2.6.159.1.1.140.0"
"ibmSystemSmartDisk"                    "1.3.6.1.4.1.2.6.159.1.1.150"
"ibmSystemSmartDiskUp"                  "1.3.6.1.4.1.2.6.159.1.1.150.0"
"ibmSystemRaid"                 "1.3.6.1.4.1.2.6.159.1.1.200"
"ibmSystemRaidUp"                       "1.3.6.1.4.1.2.6.159.1.1.200.0"
"ibmSystemAgentPlatform"                        "1.3.6.1.4.1.2.6.159.1.1.2000"
"ibmSystemAgentPlatformInfo"                    "1.3.6.1.4.1.2.6.159.1.1.2000.0"
"ibmSystemAgentV2"                      "1.3.6.1.4.1.2.6.159.1.1.2010"
"ibmSystemAssetIDV2"                    "1.3.6.1.4.1.2.6.159.1.1.2060"
"ibmSystemLMSensorV2"                   "1.3.6.1.4.1.2.6.159.1.1.2080"
"ibmSystemNetworkV2"                    "1.3.6.1.4.1.2.6.159.1.1.2110"
"ibmSystemMemoryV2"                     "1.3.6.1.4.1.2.6.159.1.1.2120"
"ibmSystemPowerV2"                      "1.3.6.1.4.1.2.6.159.1.1.2130"
"ibmSystemProcessorV2"                  "1.3.6.1.4.1.2.6.159.1.1.2140"
"ibmQLogic"                     "1.3.6.1.4.1.2.6.159.1.1.2310"
"ibmBrocade"                    "1.3.6.1.4.1.2.6.159.1.1.2320"
"ibmStorage"                    "1.3.6.1.4.1.2.6.159.3"

[fabric]

Thank you for the answer.

I have some questions more (sorry for this but these are my first approaches to SNMP).

1.
Some OIDs show a right data, for example the temperature thresholds, but other OIDs show a wrong data, for example the temperature OID shows 18° while the IMM shows 20°.
Is it normal I see this difference?

2.
Some OIDs are very long, for example the OID for the temperature is: .1.3.6.1.4.1.2.6.159.1.1.80.1.1.2.27.97.109.98.105.101.110.116.32.116.101.109.112.58.50.102.50.98.48.49.102.52.53.48.49.102.53.99
Is this normal?

3.
Other OIDs doesn’t give me any answers, as "ibmSystemRaidUp" "1.3.6.1.4.1.2.6.159.1.1.200.0"
while other OIDs give me Timeout: No Response, as "ibmSystemRaid" "1.3.6.1.4.1.2.6.159.1.1.200"
Is also this a normal behaviour of the system?

4.
About the MIB file, I get it from the installation path of the IBM System Director.
Is it supposed to be the right MIB file?
When I asked about the X3650M2 MIB on the IBM forum, I get this answer, but to be honest I don't know how use the files they linked.

5.
In the end, how did you translate the MIB file? Is there any tool for this?

Sorry for so many questions and thank your for your patience.

[tgriep]

1. If you are measuring the actual temperature, it could be different because of when the temperature was measured at that time.
2. Yes, some OIDs can be large.
3. Think of the OID as a path to the data, you will get the data from the last number in the OID but not the previous number.
4. I don't know if that MID file is correct for your device. If you downloaded from the device, I would assume it is.
5. There is a tool that should be installed on your Linux system called snmptranslate and this is how I ran it to translate your MIB snmptranslate -m IBM-SYSTEM-MIB.txt -Tz
You can search and find a lot of tools to translate OID's.