Metrics show only data from SNMP checks

This support forum board is for support questions relating to Nagios XI, our flagship commercial network monitoring solution.
avandemore
Posts: 1597
Joined: Tue Sep 27, 2016 4:57 pm

Re: Metrics show only data from SNMP checks

Post by avandemore »

Profile received and saved on shared drive. I will follow up on this soon.
Previous Nagios employee
avandemore
Posts: 1597
Joined: Tue Sep 27, 2016 4:57 pm

Re: Metrics show only data from SNMP checks

Post by avandemore »

Can you try editing /usr/local/nagios/etc/pnp/process_perfdata.cfg and change the TIMEOUT value to something like 20? Wait for about 15 minutes and see if that changed anything.

Also please send a screenshot of the Run Check Command for a bad service. XI > Configure > CCM > [Bad service] > Run Check Command.
Previous Nagios employee
richelieu
Posts: 24
Joined: Mon Dec 07, 2015 6:04 am

Re: Metrics show only data from SNMP checks

Post by richelieu »

Hi,
Is there anything new?
Do you need more information?
Regards,
Marek
avandemore
Posts: 1597
Joined: Tue Sep 27, 2016 4:57 pm

Re: Metrics show only data from SNMP checks

Post by avandemore »

Can you provide the information I requested my last post?

Thanks
Previous Nagios employee
richelieu
Posts: 24
Joined: Mon Dec 07, 2015 6:04 am

Re: Metrics show only data from SNMP checks

Post by richelieu »

Hi,
sorry for delay, I was a little confused by not finding your reply at the bottom, but now I found the second page :)
I've tried to change timeout value, but it has no effect.
I've also uploaded examples of Run check command outputs.
Regards,
Marek
You do not have the required permissions to view the files attached to this post.
avandemore
Posts: 1597
Joined: Tue Sep 27, 2016 4:57 pm

Re: Metrics show only data from SNMP checks

Post by avandemore »

Can you go to XI > Home > Service Detail > [Bad service] > Advanced tab and send a screenshot of that?

Edit the file /usr/local/nagios/etc/pnp/process_perfdata.cfg and change LOG_LEVEL = 2. Wait for the service to try and process performance data eg 15 minutes. Then send the file /usr/local/nagios/var/perfdata.log. After that, you can restore LOG_LEVEL = 0.
Previous Nagios employee
richelieu
Posts: 24
Joined: Mon Dec 07, 2015 6:04 am

Re: Metrics show only data from SNMP checks

Post by richelieu »

Hi,
I'm sending requested screenshots and perfdata.log (with LOG_LEVEL=2) file.
Regards,
Marek
You do not have the required permissions to view the files attached to this post.
avandemore
Posts: 1597
Joined: Tue Sep 27, 2016 4:57 pm

Re: Metrics show only data from SNMP checks

Post by avandemore »

According the logs that data is being updated properly. Can you submit a ticket on this? Send an email to [email protected] and reference this thread URL in it. Please reply to this thread after you have done so we know this thread can be closed.
Previous Nagios employee
richelieu
Posts: 24
Joined: Mon Dec 07, 2015 6:04 am

Re: Metrics show only data from SNMP checks

Post by richelieu »

Hi,
We've sent mail with reference to this thread to requested address to open the case.
Regards,
Marek
avandemore
Posts: 1597
Joined: Tue Sep 27, 2016 4:57 pm

Re: Metrics show only data from SNMP checks

Post by avandemore »

Did you sent that email from an email address you have on file with us?

I do not see your ticket in the queue. Please either send to that email using one you have on file, or request [email protected] to add in a new one.

Thanks, and please update this thread again when this is done.
Previous Nagios employee
Locked