db repair failed

[rtsupport]

we are using below sequence while restarting full nagios.
OS version we are using -- RHEL 7

sudo service nagios stop
sudo service httpd stop
sudo service npcd stop
sudo service ndo2db stop
sudo service mysqld stop
sudo service mariadb stop
sudo service postgresql stop
sudo service gearmand stop

sudo service gearmand start
sudo service postgresql start
sudo service mariadb start
sudo service mysqld start
sudo service ndo2db start
sudo service npcd start
sudo service httpd start
sudo service nagios start

[scottwilkerson]

In RHEL 7 this would be the preferred calls

Code: Select all

sudo systemctl stop nagios
sudo systemctl stop httpd
sudo systemctl stop npcd
sudo systemctl stop ndo2db
sudo systemctl stop mysqld
sudo systemctl stop mariadb
sudo systemctl stop postgresql
sudo systemctl stop gearmand

sudo systemctl start gearmand
sudo systemctl start postgresql
sudo systemctl start mariadb
sudo systemctl start mysqld
sudo systemctl start ndo2db
sudo systemctl start npcd
sudo systemctl start httpd
sudo systemctl start nagios

[rtsupport]

yehh i know that and if we do service start nagios then it will be also redirecting to systemctl start nagios and i don't think so this will be in issue. however next weekend we have scheduled to restart this server and at this time we will stop and start the service using systemctl and will let you know the status accordingly.

[scottwilkerson]

however next weekend we have scheduled to restart this server and at this time we will stop and start the service using systemctl and will let you know the status accordingly.

Sounds good.

[rtsupport]

today we restarted the server, We stopped all service before restart the server but we observed that all service in start status when server reboot.

is this fine or do we need to change something so that whenever server reboot we will start the service manually with correct sequence?

Also found below error while restarting gearmand service where "gearmand" folder was deleted automatically during reboot process. after creating the gearmand folder under /var/run service restarted.

Code: Select all

bash-4.2$ sudo systemctl status gearmand
● gearmand.service - LSB: start and stop the Gearman server
   Loaded: loaded (/etc/rc.d/init.d/gearmand; bad; vendor preset: disabled)
   Active: failed (Result: timeout) since Wed 2019-01-23 07:32:37 EST; 2min 37s ago
     Docs: man:systemd-sysv-generator(8)
  Process: 9673 ExecStart=/etc/rc.d/init.d/gearmand start (code=exited, status=0/SUCCESS)
   CGroup: /system.slice/gearmand.service
           └─9745 /usr/sbin/gearmand -d --worker-wakeup=10 --retention-file=/tmp/gearmand.retention -q retention --log-file=/var/log/gea...

Jan 23 07:27:37 usa0300lv1126 systemd[1]: Starting LSB: start and stop the Gearman server...
Jan 23 07:27:38 usa0300lv1126 runuser[9709]: pam_unix(runuser:session): session opened for user gearmand by (uid=0)
Jan 23 07:27:38 usa0300lv1126 gearmand[9673]: Starting gearmand: [  OK  ]
Jan 23 07:27:38 usa0300lv1126 gearmand[9673]: /etc/rc.d/init.d/gearmand: line 43: /var/run/gearmand/gearmand.pid: No such file or directory
Jan 23 07:27:38 usa0300lv1126 systemd[1]: PID file /var/run/gearmand/gearmand.pid not readable (yet?) after start.
Jan 23 07:32:37 usa0300lv1126 systemd[1]: gearmand.service start operation timed out. Terminating.
Jan 23 07:32:37 usa0300lv1126 systemd[1]: Failed to start LSB: start and stop the Gearman server.
Jan 23 07:32:37 usa0300lv1126 systemd[1]: Unit gearmand.service entered failed state.
Jan 23 07:32:37 usa0300lv1126 systemd[1]: gearmand.service failed.
Hint: Some lines were ellipsized, use -l to show in full.

[scottwilkerson]

This all sounds fine except the gearman problem

You may want to edit /etc/rc.d/init.d/gearmand to add the following above line 43

Code: Select all

mkdir -p /var/run/gearmand

[rtsupport]

is that fine?

FROM

Code: Select all

gearmand=/usr/sbin/gearmand
prog=gearmand

RETVAL=0

start() {
        echo -n $"Starting $prog: "
        daemon --pidfile=$pidfile --user=gearmand $gearmand -d $OPTIONS
        RETVAL=$?
        echo
        [ $RETVAL = 0 ] && (touch $lockfile; pgrep -f $gearmand > $pidfile)
        return $RETVAL

TO

Code: Select all

gearmand=/usr/sbin/gearmand
prog=gearmand

RETVAL=0

start() {
        echo -n $"Starting $prog: "
        daemon --pidfile=$pidfile --user=gearmand $gearmand -d $OPTIONS
        RETVAL=$?
        echo
	mkdir -p /var/run/gearmand
        [ $RETVAL = 0 ] && (touch $lockfile; pgrep -f $gearmand > $pidfile)
        return $RETVAL

[scottwilkerson]

that should do it

[rtsupport]

ok, thank you! i will make the changes, and as we are good as of now you may close the thread now/

Thank you! again Scott, for your advise.

[scottwilkerson]

ok, thank you! i will make the changes, and as we are good as of now you may close the thread now/

Thank you! again Scott, for your advise.

Great!

Locking thread